Courses & Units
Industrial Experience KNE390
Hobart
Introduction
Completion of 12 weeks of approved Industrial Experience is required for admission to BE degree. The Industrial Experience may be taken at any time during the Engineering Degree course if prerequisites are met, but is most commonly completed during the summer between third and fourth year. Students are expected to enrol in KNE389 Industrial Placement Preparation well prior to commencing their work placement so that they appear on the class list of students seeking placements, otherwise no assistance can be provided for finding placements. Students then enrol in KNE390 Industrial Experience in the semester immediately following the completion of their work experience requirements, and are required to submit a satisfactory report on the nature and extent of the work undertaken. Submission of the report is normally expected two weeks after the beginning of the Semester of enrolment. The School reserves the right to contact employers and consider their views in assessing student reports.
Summary
| Unit name | Industrial Experience |
|---|---|
| Unit code | KNE390 |
| Credit points | 12.5 |
| Faculty/School | College of Sciences and Engineering School of Engineering |
| Discipline | Engineering |
| Coordinator | |
| Teaching staff | |
| Level | Advanced |
| Available as student elective? | No |
| Breadth Unit? | No |
Availability
| Location | Study period | Attendance options | Available to | ||
|---|---|---|---|---|---|
| Hobart | Summer school | On-Campus | International | Domestic | |
| Hobart | Semester 1 - other | On-Campus | International | Domestic | |
| Hobart | Semester 2 - other | On-Campus | International | Domestic | |
Key
- On-campus
- Off-Campus
- International students
- Domestic students
Note
Please check that your computer meets the minimum System Requirements if you are attending via Distance/Off-Campus.
Units are offered in attending mode unless otherwise indicated (that is attendance is required at the campus identified). A unit identified as offered by distance, that is there is no requirement for attendance, is identified with a nominal enrolment campus. A unit offered to both attending students and by distance from the same campus is identified as having both modes of study.
Special approval is required for enrolment into TNE Program units.
TNE Program units special approval requirements.
Key Dates
| Study Period | Start date | Census date | WW date | End date |
|---|---|---|---|---|
| Summer school | 2/1/2020 | 13/1/2020 | 28/1/2020 | 23/2/2020 |
| Semester 1 - other | 24/2/2020 | 23/3/2020 | 13/4/2020 | 31/5/2020 |
| Semester 2 - other | 13/7/2020 | 10/8/2020 | 31/8/2020 | 18/10/2020 |
* The Final WW Date is the final date from which you can withdraw from the unit without academic penalty, however you will still incur a financial liability (see withdrawal dates explained for more information).
Unit census dates currently displaying for 2020 are indicative and subject to change. Finalised census dates for 2020 will be available from the 1st October 2020.
Fees
Domestic
| Band | CSP Student Contribution | Full Fee Paying (domestic) | Field of Education |
|---|---|---|---|
| 2 | 2020: $1,190.00 | 2020: $2,798.00 | 039999 |
Fees for next year will be published in October. The fees above only apply for the year shown.
Please note: international students should refer to this page to get an indicative course cost.
Requisites
Prerequisites
Teaching
| Teaching Pattern | Students need to complete 12 weeks of Industrial placement. |
|---|---|
| Assessment | Ungraded Pass based on completion of Industrial placement(s) totalling at least 12 weeks and submission of a satisfactory report - 100%. |
| Timetable | View the lecture timetable | View the full unit timetable |
Textbooks
| Required | |
|---|---|
| Recommended |
Co-op Bookshop links
The University reserves the right to amend or remove courses and unit availabilities, as appropriate.